Logo

P0772 Engine Trouble Code

P0772 Engine

When you check engine light came on code P0772 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P0772 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

Theoretically you can drive a few more days or even months with a broken MAF sensor in your car. You will notice a decrease in gas mileage/km and over time the car will at the end start stalling a lot from engine side. At a shop, the replacement cost is between $300-$450 depending on the car, but that's usually the cost of parts because the labor is relatively simple.

P0772 Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
0
Intake Valve Control Solenoid Circuit Low
7
Throttle/Pedal Position Sensor/Switch A Circuit Intermittent
7
Injection lump Fuel Metering Control 'B' High (Cam/Rotor/Injector)
2
Crankshaft Position Sensor A Circuit Low Input

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P0772 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P0772 OBD-II Trouble Code Shift solenoid valve E is turned ON or OFF by the Transmission Control Module (TCM) in response to signals sent from the park/neutral position (PNP) switch, vehicle speed and Engine Control Module ( P0772 code. Throttle/Pedal Position Sensor/Switch A Circuit Intermittent and Injection lump Fuel Metering Control 'B' High (Cam/Rotor/Injector) causes most of code P0772.

Reason For P0772 Code

The reason of P0772 OBD-II Engine Trouble Code is Throttle/Pedal Position Sensor/Switch A Circuit Intermittent.

Your car parts or components should not be replaced with reference to only a P0772 DTC. The vehicle service manual should be consulted for more information on possible causes of the error code, along with required testing.

How To Repair P0772 Code

Before starting let's see P0772 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P0772 code stored in the ECU.
  • Technicians will note P0772 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

A bad fuel pressure regulator can result in an accumulation of too much gasoline/diesel that causes your engine to backfire or the fuel to smell when you slow down your vehicle. If you see even a slight problem, it is essential to have it inspected to quickly correct any issues before any damage is further imposed on your car.

If nothing is done to repair the persistent P0772 code, the ECU will put the vehicle into a limp mode. This mode limits the top speed and reduces engine power greatly to protect the engine.

Sometimes P0772 code comes with P077200 code.

Diagnosis Of Engine Error OBD Code P0772

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P0772 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P0772 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.